| Vorheriges Thema anzeigen :: Nächstes Thema anzeigen |
| Autor |
Nachricht |
cooltouch
 Anmeldungsdatum: 15.01.2009 Beiträge: 9096 Wohnort: Houston, Texas
|
 Verfasst am: So Jan 02, 2011 9:55 pm Titel: DIY Jobo-style processor? |
|
 Verfasst am: So Jan 02, 2011 9:55 pm Titel: DIY Jobo-style processor? |
|
|
cooltouch wrote:
Right now I just use a Patterson tank and reels to develop my B&W film, but I'd like to get back into developing color again, especially slides because it's become so inconvenient and expensive to have them developed. Way back in the 80s I used to develop my own slides, and it was a real hassle trying to keep my bath at +/- 1/2 degree F, so it's gotten me to wonder just how difficult it would be to build a tank that would hold a bath at an exact temperature. I'm thinking it would actually be pretty easy.
In my case, I wouldn't need the rollers that some Jobo systems have or the lifts or whatever other gizmos they contain -- just room enough for the bottled chems to be put in the bath and to roll around the developing tank manually. Or maybe I could just agitate it every 30 seconds or so the way I do it with my B&W films. That would still work as well I'm thinking. I also have a couple of the tanks with the spinners for agitation. They seem to work fin for 35mm, but I've gotten streaks with my 120 when using them, so I don't use them anymore -- at least for 120.
Ever seen a heater used in reptile terrariums? It's just a large flat plastic pad with a heating element inside and with an adhesive side so it can be pasted onto the terrarium tank's bottom surface. It plugs into a wall socket and heats up to raise the temperature far enough inside the terrarium so the reptiles are comfortable -- probably with an air temperature around 105F to 110F. This is most likely too warm for color chems, but one can rig a dimmer switch up to an outlet box to control temperature.
So just wondering if anyone else here has had thoughts along these lines and what, if anything, you might have come up with? _________________ Michael
My Gear List: http://michaelmcbroom.com/photo/gear.html
My Gallery: http://michaelmcbroom.com/gallery3/index.php/
My Flickr Page: https://www.flickr.com/photos/11308754@N08/albums
My Music: https://soundcloud.com/michaelmcbroom/albums
My Blog: http://michaelmcbroom.com/blogistan/ |
|
| Nach oben |
|
 |
Attila
 Anmeldungsdatum: 24.02.2007 Beiträge: 58002
Expire: 2025-11-18
|
 Verfasst am: So Jan 02, 2011 10:05 pm Titel: |
|
 Verfasst am: So Jan 02, 2011 10:05 pm Titel: |
|
|
Attila wrote:
I did develop myself slides 25 years ago I did put simple developer tank into bathroom and I did put fine temperature water to bathtub. I don't remember for difficulties, lot's of water did cool down slowly I think safe enough to develop slides. |
|
| Nach oben |
|
 |
cooltouch
 Anmeldungsdatum: 15.01.2009 Beiträge: 9096 Wohnort: Houston, Texas
|
 Verfasst am: So Jan 02, 2011 10:32 pm Titel: |
|
 Verfasst am: So Jan 02, 2011 10:32 pm Titel: |
|
|
cooltouch wrote:
Back in the 80s when I did it, I used my bathroom sink as the developer bath and used ice cubes to fine tune the temperature. The temp stayed relatively stable once I got it where I wanted it, but I can recall having to fiddle with things for quite a while before getting it to settle at the right temperature. This is what I'm trying to avoid with a temperature-controlled bath. _________________ Michael
My Gear List: http://michaelmcbroom.com/photo/gear.html
My Gallery: http://michaelmcbroom.com/gallery3/index.php/
My Flickr Page: https://www.flickr.com/photos/11308754@N08/albums
My Music: https://soundcloud.com/michaelmcbroom/albums
My Blog: http://michaelmcbroom.com/blogistan/ |
|
| Nach oben |
|
 |
marty
 Anmeldungsdatum: 09.04.2009 Beiträge: 767 Wohnort: Italy
|
 Verfasst am: So Jan 02, 2011 11:45 pm Titel: |
|
 Verfasst am: So Jan 02, 2011 11:45 pm Titel: |
|
|
marty wrote:
That would be an interesting project. At the moment I'm developing C-41 keeping the tank (the type with the spinning rod) in a water bath within a plastic tub. I start a couple of degrees above 38°C, I'm able to maintain the temp correct during the development then starts to drop but it's not critical at that point. I warm up the chemicals at 38°C before to start with the same water bath. The negs look fine to me, I'm able to make RA-4 prints with reasonable consistency. I've done E-6 too with the same method, it's a bit trickier here because the temp has to stay at 38°C during the two development phases. I kept a thermometer in the tub and added hot water from the tap when the temperature was dropping. The slides look fine to me. I'm not pretending is a perfect method but works for me. I have not great numbers to process and usually I'm not in a hurry. Failing that I think it's going to become unpractical. And of course I'm not pro and even if I screw something nobody's gonna lose anything (not yet happened so far).
That's my experience for what's worth. Now a link that may be interesting, looks simple enough and inexpensive too: http://www.dunnamphoto.com/tempering_tray.htm
And another one probably useful to a more advanced kind of hobbyst:
http://ludens.cl/photo/processor/processor.html
Cheers, M. _________________ Canon FD
Bodies: AT-1, A-1, T-90
Lenses: nFD 20mm f2.8, 24 f2.8, 28 f2.8, 35 f2, FD 50 f1.8 S.C., 85 f1.8, 100 f2.8, 135 f2.8, 200 f4, 300 f4
|
|
| Nach oben |
|
 |
cooltouch
 Anmeldungsdatum: 15.01.2009 Beiträge: 9096 Wohnort: Houston, Texas
|
 Verfasst am: Mo Jan 03, 2011 5:34 am Titel: |
|
 Verfasst am: Mo Jan 03, 2011 5:34 am Titel: |
|
|
cooltouch wrote:
Thanks for the links, Marty. More to think about. _________________ Michael
My Gear List: http://michaelmcbroom.com/photo/gear.html
My Gallery: http://michaelmcbroom.com/gallery3/index.php/
My Flickr Page: https://www.flickr.com/photos/11308754@N08/albums
My Music: https://soundcloud.com/michaelmcbroom/albums
My Blog: http://michaelmcbroom.com/blogistan/ |
|
| Nach oben |
|
 |
|
|
|
Du kannst keine Beiträge in dieses Forum schreiben. Du kannst auf Beiträge in diesem Forum nicht antworten. Du kannst deine Beiträge in diesem Forum nicht bearbeiten. Du kannst deine Beiträge in diesem Forum nicht löschen. Du kannst an Umfragen in diesem Forum nicht mitmachen.
|