| Vorheriges Thema anzeigen :: Nächstes Thema anzeigen |
| Autor |
Nachricht |
Fujinonuser
 Anmeldungsdatum: 06.01.2011 Beiträge: 128 Wohnort: Germany
|
 Verfasst am: Mo Jan 14, 2013 11:59 pm Titel: M42-to-PK adapter with inner flange |
|
 Verfasst am: Mo Jan 14, 2013 11:59 pm Titel: M42-to-PK adapter with inner flange |
|
|
Fujinonuser wrote:
This topic has been discussed in 2008, when a member from Hongkong, who in the meantime has left mflenses, sold M42-to-PK adapters with an inner flange to press down the aperture pin with M42 lenses that lack an A/M switch. Such M42 adapters are widely available in the Bay for almost all camera systems, but they are totally absent for the Pentax PK bayonet. Why? Has anyone got a plausible answer? Is there anyone willing to sell me such an adapter or who could point me to a source where I might order such an adapter?
On the other hand, I would be grateful for a selection of the best solutions to reversibly press down the aperture pin of a M42 lens so that stopping down the lens will be possible, preferrably without opening the lens. Thanks for your input. |
|
| Nach oben |
|
 |
visualopsins
 Anmeldungsdatum: 05.03.2009 Beiträge: 11698 Wohnort: California
Expire: 2027-07-11
|
 Verfasst am: Di Jan 15, 2013 12:15 am Titel: |
|
 Verfasst am: Di Jan 15, 2013 12:15 am Titel: |
|
|
visualopsins wrote:
M42 and PK have the same camera register -- the distance from lens mount surface to film/sensor -- thus, any adapter must have zero thickness for lens to focus all the way to infinity, otherwise the adapter acts as an extension tube preventing infinity focus.
Folks have used various means of keeping the diaphragm pin depressed, such as a drop of super glue (reversible with acetone). _________________ ☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮ like attracts like! ☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮
Cameras: Sony ILCE-7RM2, Spotmatics II, F, and ESII, Nikon P4
Lenses:
M42 Asahi Optical Co., Takumar 1:4 f=35mm, 1:2 f=58mm (Sonnar), 1:2.4 f=58mm (Heliar), 1:2.2 f=55mm (Gaussian), 1:2.8 f=105mm (Model I), 1:2.8/105 (Model II), 1:5.6/200, Tele-Takumar 1:5.6/200, 1:6.3/300, Macro-Takumar 1:4/50, Auto-Takumar 1:2.3 f=35, 1:1.8 f=55mm, 1:2.2 f=55mm, Super-TAKUMAR 1:3.5/28 (fat), 1:2/35 (Fat), 1:1.4/50 (8-element), Super-Multi-Coated Fisheye-TAKUMAR 1:4/17, Super-Multi-Coated TAKUMAR 1:4.5/20, 1:3.5/24, 1:3.5/28, 1:2/35, 1:3.5/35, 1:1.8/85, 1:1.9/85 1:2.8/105, 1:3.5/135, 1:2.5/135 (II), 1:4/150, 1:4/200, 1:4/300, 1:4.5/500, Super-Multi-Coated Macro-TAKUMAR 1:4/50, 1:4/100, Super-Multi-Coated Bellows-TAKUMAR 1:4/100, SMC TAKUMAR 1:1.4/50, 1:1.8/55
M42 Carl Zeiss Jena Flektogon 2.4/35
Contax Carl Zeiss Vario-Sonnar T* 28-70mm F3.5-4.5
Pentax K-mount SMC PENTAX-A ZOOM 1:3.5 35~105mm, SMC PENTAX ZOOM 1:4 45~125mm
Nikon Micro-NIKKOR-P-C Auto 1:3.5 f=55mm, NIKKOR-P Auto 105mm f/2.5 Pre-AI (Sonnar), Micro-NIKKOR 105mm 1:4 AI, NIKKOR AI-S 35-135mm f/3,5-4,5
Solinon 1:5.6/18 ASPH.
Tamron SP 17mm f/3.5 (51B), Tamron SP 17mm f/3.5 (151B), SP 500mm f/8 (55BB), SP 70-210mm f/3.5 (19AH)
Vivitar 100mm 1:2.8 MC 1:1 Macro Telephoto (Kiron)
|
|
| Nach oben |
|
 |
kuuan
 Anmeldungsdatum: 14.01.2008 Beiträge: 4569 Wohnort: right now: Austria
Expire: 2014-12-26
|
|
| Nach oben |
|
 |
CarbonR
 Anmeldungsdatum: 31.12.2008 Beiträge: 1985 Wohnort: Auvergne, France
|
 Verfasst am: Di Jan 15, 2013 6:15 am Titel: |
|
 Verfasst am: Di Jan 15, 2013 6:15 am Titel: |
|
|
CarbonR wrote:
| visualopsins hat folgendes geschrieben:: |
M42 and PK have the same camera register -- the distance from lens mount surface to film/sensor -- thus, any adapter must have zero thickness for lens to focus all the way to infinity, otherwise the adapter acts as an extension tube preventing infinity focus.
Folks have used various means of keeping the diaphragm pin depressed, sucIh as a drop of super glue (reversible with acetone). |
I have one of these adapters from hk300 and infity is kept, the inner flange is very useful  _________________ Here lies my signature. |
|
| Nach oben |
|
 |
Fujinonuser
 Anmeldungsdatum: 06.01.2011 Beiträge: 128 Wohnort: Germany
|
 Verfasst am: Di Jan 15, 2013 9:51 am Titel: |
|
 Verfasst am: Di Jan 15, 2013 9:51 am Titel: |
|
|
Fujinonuser wrote:
Thank you for your input, especiall to kuuan. The Kindai and Kipon adapters that you mention seem to have an outer flange as well so that infinity will not be reached with those adapters. I can't understand why such adapters with inner flange and without outer flange should not be available commercially in great numbers, considering the fact that Pentax DSLRs are ideally suited for M42 lenses. It would be good if mflenses members had contacts to Chinese producers of photo accessories. I'm sure there is a wide demand for such adapters.
The next best solution seems to be super-glue, yet I will first try if aceton will remove the glue effectively again. As I'm not a very talented guy with practical work, I would of course highly appreciate if some member has the time to shoot some inspirational photos of how he does the job. Thanks to all. |
|
| Nach oben |
|
 |
peterqd
 Anmeldungsdatum: 28.02.2007 Beiträge: 7449 Wohnort: near High Wycombe, UK
Expire: 2014-01-04
|
 Verfasst am: Di Jan 15, 2013 10:35 am Titel: |
|
 Verfasst am: Di Jan 15, 2013 10:35 am Titel: |
|
|
peterqd wrote:
There are various different non-destructive methods of keeping the pin (or the components underneath it) depressed, depending on the
model of lens itself. Superglue is not the most reliable or easiest to reverse method in my experience. Which lens are you interested in? _________________ Peter - Moderator |
|
| Nach oben |
|
 |
kuuan
 Anmeldungsdatum: 14.01.2008 Beiträge: 4569 Wohnort: right now: Austria
Expire: 2014-12-26
|
 Verfasst am: Di Jan 15, 2013 10:46 am Titel: |
|
 Verfasst am: Di Jan 15, 2013 10:46 am Titel: |
|
|
kuuan wrote:
| Fujinonuser hat folgendes geschrieben:: |
| Thank you for your input, especiall to kuuan. The Kindai and Kipon adapters that you mention seem to have an outer flange as well so that infinity will not be reached with those adapters. |
look again! I don't know any Kipon adapter and didn't mention any. The Kindai adapter I linked to sits inside the K mount exactly like the 'original' Pentax adapter, does NOT have an outer flange and certainly allows for infinity. _________________ my photos on flickr: https://www.flickr.com/photos/kuuan/collections
Zuletzt bearbeitet von kuuan am Di Jan 15, 2013 11:05 am, insgesamt ein Mal bearbeitet |
|
| Nach oben |
|
 |
Lloydy
 Anmeldungsdatum: 02.09.2009 Beiträge: 7880 Wohnort: Ironbridge. UK.
Expire: 2022-01-01
|
 Verfasst am: Di Jan 15, 2013 11:05 am Titel: |
|
 Verfasst am: Di Jan 15, 2013 11:05 am Titel: |
|
|
Lloydy wrote:
http://www.ebay.com/itm/New-kipon-adapter-for-Carl-Zeiss-M42-mount-lens-to-Pentax-K-PK-camera-/121023991840?pt=US_Lens_Adapters_Mounts_Tubes&hash=item1c2d979020&afsrc=1
That's the thing, I haven't got one but that looks like it sits flush and allows infinity. _________________ LENSES & CAMERAS FOR SALE.....
I have loads of stuff that I have to get rid of, if you see me commenting about something I have got and you want one, ask me.
My Flickr https://www.flickr.com/photos/mudplugga/
My ipernity -
http://www.ipernity.com/home/294337 |
|
| Nach oben |
|
 |
kuuan
 Anmeldungsdatum: 14.01.2008 Beiträge: 4569 Wohnort: right now: Austria
Expire: 2014-12-26
|
 Verfasst am: Di Jan 15, 2013 11:06 am Titel: |
|
 Verfasst am: Di Jan 15, 2013 11:06 am Titel: |
|
|
kuuan wrote:
| Lloydy hat folgendes geschrieben:: |
http://www.ebay.com/itm/New-kipon-adapter-for-Carl-Zeiss-M42-mount-lens-to-Pentax-K-PK-camera-/121023991840?pt=US_Lens_Adapters_Mounts_Tubes&hash=item1c2d979020&afsrc=1
That's the thing, I haven't got one but that looks like it sits flush and allows infinity. |
oh nice, looks good, definitely no outer flange neither and for half the money of the Kindai ( which really is a top quality precision product ) _________________ my photos on flickr: https://www.flickr.com/photos/kuuan/collections |
|
| Nach oben |
|
 |
peterqd
 Anmeldungsdatum: 28.02.2007 Beiträge: 7449 Wohnort: near High Wycombe, UK
Expire: 2014-01-04
|
 Verfasst am: Di Jan 15, 2013 11:17 am Titel: |
|
 Verfasst am: Di Jan 15, 2013 11:17 am Titel: |
|
|
peterqd wrote:
I dislike internal flanges intensely now, after numerous infinity focus problems:
- The rear element of some lenses is too large to pass through the reduced opening (e.g. S-Tak 1.4/50)
- The pin on some lenses won't depress far enough to allow the lens to be fully screwed in.
- Some lenses have projections and levers which conflict with the flange (e.g. S-M-C Taks)
If you use lenses with an A-M switch then this is by far the best way of activating the diaphragm. If you have auto lenses without an
A-M switch (there are only a few of these) then a simple way of keeping the lens in manual mode is usually quite easy to find by simply
looking inside the rear mount. _________________ Peter - Moderator |
|
| Nach oben |
|
 |
kuuan
 Anmeldungsdatum: 14.01.2008 Beiträge: 4569 Wohnort: right now: Austria
Expire: 2014-12-26
|
 Verfasst am: Di Jan 15, 2013 11:33 am Titel: |
|
 Verfasst am: Di Jan 15, 2013 11:33 am Titel: |
|
|
kuuan wrote:
| peterqd hat folgendes geschrieben:: |
I dislike internal flanges intensely now, after numerous infinity focus problems:
- The rear element of some lenses is too large to pass through the reduced opening (e.g. S-Tak 1.4/50)
- The pin on some lenses won't depress far enough to allow the lens to be fully screwed in.
- Some lenses have projections and levers which conflict with the flange (e.g. S-M-C Taks)
|
I do not have any experience with any M42>K mount adapter with inner flange, BUT I have a similar problem with the inner flange of my m42>NEX adapter. Well only with one M42 lens out of around 50, I think the Pin of my S-M-C 1.8/85mm doesn't get pressed but rubs hard against the inner rim of the flange and that makes it almost impossible to turn the aperture ring _________________ my photos on flickr: https://www.flickr.com/photos/kuuan/collections |
|
| Nach oben |
|
 |
peterqd
 Anmeldungsdatum: 28.02.2007 Beiträge: 7449 Wohnort: near High Wycombe, UK
Expire: 2014-01-04
|
 Verfasst am: Di Jan 15, 2013 1:39 pm Titel: |
|
 Verfasst am: Di Jan 15, 2013 1:39 pm Titel: |
|
|
peterqd wrote:
| kuuan hat folgendes geschrieben:: |
| peterqd hat folgendes geschrieben:: |
I dislike internal flanges intensely now, after numerous infinity focus problems:
- The rear element of some lenses is too large to pass through the reduced opening (e.g. S-Tak 1.4/50)
- The pin on some lenses won't depress far enough to allow the lens to be fully screwed in.
- Some lenses have projections and levers which conflict with the flange (e.g. S-M-C Taks)
|
I do not have any experience with any M42>K mount adapter with inner flange, BUT I have a similar problem with the inner flange of my m42>NEX adapter. Well only with one M42 lens out of around 50, I think the Pin of my S-M-C 1.8/85mm doesn't get pressed but rubs hard against the inner rim of the flange and that makes it almost impossible to turn the aperture ring |
That would be the lever that communicates with the camera Andreas, not the pin, and I expect it's not only jamming the aperture dial but
also preventing infinity focus. There's also a kind of small block moulded on the mount of S-M-C Taks I don't know the purpose of it.
Normally it sits inside the mount on an M42 camera, but it jams against the inner flange too and stops the lens screwing in fully.
All my S-M-C Taks bind on my M42>EOS adapter, I had to make the opening larger by grinding. I removed the inner flange completely
on my NEX adapter, it was like a large loose washer  _________________ Peter - Moderator |
|
| Nach oben |
|
 |
kuuan
 Anmeldungsdatum: 14.01.2008 Beiträge: 4569 Wohnort: right now: Austria
Expire: 2014-12-26
|
 Verfasst am: Di Jan 15, 2013 4:47 pm Titel: |
|
 Verfasst am: Di Jan 15, 2013 4:47 pm Titel: |
|
|
kuuan wrote:
| peterqd hat folgendes geschrieben:: |
That would be the lever that communicates with the camera Andreas, not the pin, and I expect it's not only jamming the aperture dial but also preventing infinity focus. |
yes Peter, of course you are right, it is the lever that has a lot of friction on the inside of the inner flange of the adapter if I screwed the lens all in, then already with some force. However it looks as if somewhat reducing the diameter of the inner flange of the adapter would solve this problem, and that then all my M42 lenses might work perfectly well with this adapter. _________________ my photos on flickr: https://www.flickr.com/photos/kuuan/collections |
|
| Nach oben |
|
 |
DigiChromeEd
 Anmeldungsdatum: 29.12.2009 Beiträge: 3468 Wohnort: Northern Ireland
|
 Verfasst am: Di Jan 15, 2013 5:04 pm Titel: |
|
 Verfasst am: Di Jan 15, 2013 5:04 pm Titel: |
|
|
DigiChromeEd wrote:
| peterqd hat folgendes geschrieben:: |
All my S-M-C Taks bind on my M42>EOS adapter, I had to make the opening larger by grinding. I removed the inner flange completely on my NEX adapter, it was like a large loose washer  |
I have ordered a couple of M42-NEX adapters in the past from big_is on eBay and they have come with two removable mounts, one with flange and one without. _________________ "I've got a Nikon camera, I like to take a photograph" - Paul Simon |
|
| Nach oben |
|
 |
kuuan
 Anmeldungsdatum: 14.01.2008 Beiträge: 4569 Wohnort: right now: Austria
Expire: 2014-12-26
|
 Verfasst am: Di Jan 15, 2013 5:50 pm Titel: |
|
 Verfasst am: Di Jan 15, 2013 5:50 pm Titel: |
|
|
kuuan wrote:
| DigiChromeEd hat folgendes geschrieben:: |
| peterqd hat folgendes geschrieben:: |
All my S-M-C Taks bind on my M42>EOS adapter, I had to make the opening larger by grinding. I removed the inner flange completely on my NEX adapter, it was like a large loose washer  |
I have ordered a couple of M42-NEX adapters in the past from big_is on eBay and they have come with two removable mounts, one with flange and one without. |
that's the one I am having too, but by accident they had sent me 2 mounts with flange, time I cut off the flange of one of them  _________________ my photos on flickr: https://www.flickr.com/photos/kuuan/collections |
|
| Nach oben |
|
 |
Fujinonuser
 Anmeldungsdatum: 06.01.2011 Beiträge: 128 Wohnort: Germany
|
 Verfasst am: Mo Jan 21, 2013 12:47 pm Titel: |
|
 Verfasst am: Mo Jan 21, 2013 12:47 pm Titel: |
|
|
Fujinonuser wrote:
That's magic! Sometimes it seems to help just to speak about your problems and -- alas, there is the solution. The Kipon adapter with inner flange looks very good indeed. In the meantime, I have found another flange adapter selling cheaply at ebay.de, and and I'm still waiting for it to arrive:
http://www.ebay.de/itm/Adapter-Objektivadapter-Unendlich-Infitity-M42-M-42-fur-Pentax-K-K-x-K-5-K-r-K-m-/170976649736?pt=DE_Foto_Camcorder_Objetivanschl%C3%BCsse_Adapter&hash=item27cf00a208
I agree with Peter that there are some -- luckily only few -- lenses with large rear element that won't fit through the adapter's opening, yet generally I would expect that all lenses fitting to a Canon EOS flange adapter should also fit to a Pentax PK adapter, or am I wrong here?
Again, thanks for your input! |
|
| Nach oben |
|
 |
kuuan
 Anmeldungsdatum: 14.01.2008 Beiträge: 4569 Wohnort: right now: Austria
Expire: 2014-12-26
|
 Verfasst am: Di Jan 22, 2013 5:19 pm Titel: |
|
 Verfasst am: Di Jan 22, 2013 5:19 pm Titel: |
|
|
kuuan wrote:
good find!
once you have used it please report back about it's functionality ( may get one too ) _________________ my photos on flickr: https://www.flickr.com/photos/kuuan/collections |
|
| Nach oben |
|
 |
Fujinonuser
 Anmeldungsdatum: 06.01.2011 Beiträge: 128 Wohnort: Germany
|
 Verfasst am: Mi Jan 23, 2013 11:31 pm Titel: |
|
 Verfasst am: Mi Jan 23, 2013 11:31 pm Titel: |
|
|
Fujinonuser wrote:
I'll certainly report about it, Kuuan. So far it has not yet arrived, as it comes from Poland. There seem to be some attentive photographers in Poland. |
|
| Nach oben |
|
 |
dnf_spedition
 Anmeldungsdatum: 18.04.2009 Beiträge: 64 Wohnort: The Netherlands
|
 Verfasst am: Mo Jan 27, 2014 10:26 am Titel: |
|
 Verfasst am: Mo Jan 27, 2014 10:26 am Titel: |
|
|
dnf_spedition wrote:
Hello All,
I have got the Kipon innerflange M42 to K adapter last week. I tested the adapter and put it on an old Penax MV and found out that the security clip got stuck. It was not easy to remove the adapter again with the tool provided. Then I decided tot remove the little clip from the adapter. Tried again and it fits better. So I took it off the MV and put it on my Pentax K-x. Fits o.k. The only thing that I found out is that Helios 58 mm lenses does not fit. When I put the lens on the adapter and then clip the total on the camera it will not fit. When I first put on the adapter on the camera and then screw in the lens it is loose. I mean that it is not tight enough to the camera and moves back and forward. This happens with the Helios M44-4 58 mm and the M44-7. I did not test with other Helios lenses I have, but I am quite sure the same wil happen. So I believe the Kipon innerflange adapter will not operate with Helios lenses. |
|
| Nach oben |
|
 |
|
|