| Vorheriges Thema anzeigen :: Nächstes Thema anzeigen |
| Autor |
Nachricht |
iangreenhalgh1
 Anmeldungsdatum: 18.03.2011 Beiträge: 15679
Expire: 2014-01-07
|
 Verfasst am: Sa Dez 08, 2012 10:53 am Titel: Contax IIIa, Opton Biogon 2.8/35, Agfa Vista Plus 200 roll 2 |
|
 Verfasst am: Sa Dez 08, 2012 10:53 am Titel: Contax IIIa, Opton Biogon 2.8/35, Agfa Vista Plus 200 roll 2 |
|
|
iangreenhalgh1 wrote:
This is the film that is available fo 1ukp in Poundland for 36exp. Good stuff, definitely made by Fuji but not sure what emulsion it is, seems similar to Superia 200.
Most of this roll was spoilt by a shutter issue, one shutter speed on my Contax IIIa produces a black bar on one side of the frame, but the others are all fine. I haven't worked out which speed it is yet, 1/100 and 1/1250 are fine so it's either 1/250 or 1/500.
I'm still getting lots of white spots on some frames, it's wierd, some frames are an absolute snowstorm and others have very few spots. Anyone got any ideas what might be causing this?
All of these are wide open, apart from the shot of the railway lines. The Biogon is one of the few lenses I have that I think is worth shooting wide open.
#1
#2
#3
#4
#5
#6
#7
#8
#9
#10
 _________________ I don't care who designed it, who made it or what country it comes from - I just enjoy using it! |
|
| Nach oben |
|
 |
Attila
 Anmeldungsdatum: 24.02.2007 Beiträge: 58002
Expire: 2025-11-18
|
 Verfasst am: Sa Dez 08, 2012 3:42 pm Titel: |
|
 Verfasst am: Sa Dez 08, 2012 3:42 pm Titel: |
|
|
Attila wrote:
#9 is especially good, nice job! |
|
| Nach oben |
|
 |
iangreenhalgh1
 Anmeldungsdatum: 18.03.2011 Beiträge: 15679
Expire: 2014-01-07
|
 Verfasst am: Sa Dez 08, 2012 3:45 pm Titel: |
|
 Verfasst am: Sa Dez 08, 2012 3:45 pm Titel: |
|
|
iangreenhalgh1 wrote:
Cheers. No PP on #9, so it has some white spots. I think it also shows how the Russian turret finder can sometimes give you slightly off framing at close distance.  _________________ I don't care who designed it, who made it or what country it comes from - I just enjoy using it! |
|
| Nach oben |
|
 |
Excalibur
 Anmeldungsdatum: 19.07.2009 Beiträge: 5018 Wohnort: UK
Expire: 2014-04-21
|
 Verfasst am: Sa Dez 08, 2012 7:08 pm Titel: |
|
 Verfasst am: Sa Dez 08, 2012 7:08 pm Titel: |
|
|
Excalibur wrote:
When projecting onto printing paper or scanning..... white spots are usually from dust (could be temporary or stuck to the neg when drying), a large rocket blower should be used for negs and glass OR before using the blower, wipe negs with a clean cotton handkerchief. _________________ Canon A1, AV1, T70 & T90, EOS 300 and EOS300v, Chinon CE and CP-7M. Contax 139, Fuji STX-2, Konica Autoreflex TC, FS-1, FT-1, Minolta X-700, X-300, XD-11, SRT101b, Nikon EM, FM, F4, F90X, Olympus OM2, Pentax S3, Spotmatic, Pentax ME super, Praktica TL 5B, & BC1, , Ricoh KR10super, Yashica T5D, Bronica Etrs, Mamiya RB67 pro AND drum roll:- a Sony Nex 3
.........past gear Tele Rolleiflex and Rollei SL66.
Many lenses from good to excellent. |
|
| Nach oben |
|
 |
iangreenhalgh1
 Anmeldungsdatum: 18.03.2011 Beiträge: 15679
Expire: 2014-01-07
|
 Verfasst am: Sa Dez 08, 2012 7:14 pm Titel: |
|
 Verfasst am: Sa Dez 08, 2012 7:14 pm Titel: |
|
|
iangreenhalgh1 wrote:
Yes, this isn't dust unless it's getting stuck in the emulsion while it's drying. It's wierd, some frames have loads, some frames have very few. _________________ I don't care who designed it, who made it or what country it comes from - I just enjoy using it! |
|
| Nach oben |
|
 |
skida
 Anmeldungsdatum: 02.03.2012 Beiträge: 1826 Wohnort: North East England
|
 Verfasst am: Sa Dez 08, 2012 7:16 pm Titel: |
|
 Verfasst am: Sa Dez 08, 2012 7:16 pm Titel: |
|
|
skida wrote:
6 and 9 are my stand outs in this series. I love the colours we get with Vista. |
|
| Nach oben |
|
 |
iangreenhalgh1
 Anmeldungsdatum: 18.03.2011 Beiträge: 15679
Expire: 2014-01-07
|
 Verfasst am: Sa Dez 08, 2012 7:17 pm Titel: |
|
 Verfasst am: Sa Dez 08, 2012 7:17 pm Titel: |
|
|
iangreenhalgh1 wrote:
Cheers. I do like Vista, colours are good even in poor light, which is important for us up north where it's often gloomy.  _________________ I don't care who designed it, who made it or what country it comes from - I just enjoy using it! |
|
| Nach oben |
|
 |
miran
 Anmeldungsdatum: 01.08.2012 Beiträge: 1364 Wohnort: Slovenia
|
 Verfasst am: Sa Dez 08, 2012 7:24 pm Titel: |
|
 Verfasst am: Sa Dez 08, 2012 7:24 pm Titel: |
|
|
miran wrote:
About those white spots, I don't know if it's the same thing as with B&W film or something different (I only do B&W) but I find that I get more spots when the frame is underexposed. The more it is under, the more white spots there are. |
|
| Nach oben |
|
 |
iangreenhalgh1
 Anmeldungsdatum: 18.03.2011 Beiträge: 15679
Expire: 2014-01-07
|
 Verfasst am: Sa Dez 08, 2012 7:54 pm Titel: |
|
 Verfasst am: Sa Dez 08, 2012 7:54 pm Titel: |
|
|
iangreenhalgh1 wrote:
Interesting, thanks. _________________ I don't care who designed it, who made it or what country it comes from - I just enjoy using it! |
|
| Nach oben |
|
 |
Orio
Anmeldungsdatum: 24.02.2007 Beiträge: 29545 Wohnort: West Emilia
Expire: 2012-12-04
|
 Verfasst am: So Dez 09, 2012 12:45 am Titel: |
|
 Verfasst am: So Dez 09, 2012 12:45 am Titel: |
|
|
Orio wrote:
Those white spots look like calcar to me. What do you use for your bath, distilled water or tap water? _________________ Orio, Administrator
T*
NE CEDE MALIS AUDENTIOR ITO
Ferrania film is reborn! http://www.filmferrania.it/
Support the Ornano film chemicals company and help them survive!
http://forum.mflenses.com/ornano-chemical-products-t55525.html |
|
| Nach oben |
|
 |
iangreenhalgh1
 Anmeldungsdatum: 18.03.2011 Beiträge: 15679
Expire: 2014-01-07
|
 Verfasst am: So Dez 09, 2012 9:00 am Titel: |
|
 Verfasst am: So Dez 09, 2012 9:00 am Titel: |
|
|
iangreenhalgh1 wrote:
I use distilled water for my final bath. The water here is very soft indeed so probably not calcium, we never get any limescale here. _________________ I don't care who designed it, who made it or what country it comes from - I just enjoy using it! |
|
| Nach oben |
|
 |
Orio
Anmeldungsdatum: 24.02.2007 Beiträge: 29545 Wohnort: West Emilia
Expire: 2012-12-04
|
 Verfasst am: So Dez 09, 2012 1:04 pm Titel: |
|
 Verfasst am: So Dez 09, 2012 1:04 pm Titel: |
|
|
Orio wrote:
You absolutely should use demineralized water for your chemical baths as well.
Say you get some calcar or minuscule debris in tap water that you use with the developer, it may stick on the surface and prevent development of the surface in that point, hence white colour. Washing with demineralized water will not help that, undeveloped point will remain white. _________________ Orio, Administrator
T*
NE CEDE MALIS AUDENTIOR ITO
Ferrania film is reborn! http://www.filmferrania.it/
Support the Ornano film chemicals company and help them survive!
http://forum.mflenses.com/ornano-chemical-products-t55525.html |
|
| Nach oben |
|
 |
iangreenhalgh1
 Anmeldungsdatum: 18.03.2011 Beiträge: 15679
Expire: 2014-01-07
|
 Verfasst am: So Dez 09, 2012 1:31 pm Titel: |
|
 Verfasst am: So Dez 09, 2012 1:31 pm Titel: |
|
|
iangreenhalgh1 wrote:
I made my developer, bleach and fixer from distilled water. I wash the tank out between each step with running tap water, maybe this is where I'm going wrong and I need to use distilled water throughout? _________________ I don't care who designed it, who made it or what country it comes from - I just enjoy using it! |
|
| Nach oben |
|
 |
Orio
Anmeldungsdatum: 24.02.2007 Beiträge: 29545 Wohnort: West Emilia
Expire: 2012-12-04
|
 Verfasst am: So Dez 09, 2012 4:39 pm Titel: |
|
 Verfasst am: So Dez 09, 2012 4:39 pm Titel: |
|
|
Orio wrote:
| iangreenhalgh1 hat folgendes geschrieben:: |
| I made my developer, bleach and fixer from distilled water. I wash the tank out between each step with running tap water, maybe this is where I'm going wrong and I need to use distilled water throughout? |
I do not have a sure anwser, but I think it's safer not to use tap water until after you have made the first rinse (or hypo clearing bath) after fixer.
This is what I use when I don't have enough distilled water to cover all the steps:
- Pre-wash: distilled water
- Developer: distilled water
- Stop: distilled water
- Fixer: distilled water
- First rinse (10 inversions): distilled water
- Hypo Clearing (2 minutes): distilled water
- second rinse (20 inversions): tap water
- third rinse (30 inversions): tap water
- fourth rinse (40 inversions): tap water
- final rinse (10 inversions): distilled water
- wetting agent soak (30 seconds): distilled water
When I have enough water collected from my air conditioner, I replace the tap water with the air conditioned condensed water. _________________ Orio, Administrator
T*
NE CEDE MALIS AUDENTIOR ITO
Ferrania film is reborn! http://www.filmferrania.it/
Support the Ornano film chemicals company and help them survive!
http://forum.mflenses.com/ornano-chemical-products-t55525.html |
|
| Nach oben |
|
 |
iangreenhalgh1
 Anmeldungsdatum: 18.03.2011 Beiträge: 15679
Expire: 2014-01-07
|
 Verfasst am: So Dez 09, 2012 4:45 pm Titel: |
|
 Verfasst am: So Dez 09, 2012 4:45 pm Titel: |
|
|
iangreenhalgh1 wrote:
Hmm, my process is a bit simpler:
Presoak in hot tap water approx 5 mins
Developer for 3:15 at 38C
rinse under running tap for approx 2 mins
Bleach at room temp for approx 10 mins (it is to completion so timing is not important)
rinse under running tap for approx 2 mins
Fix at room temp for approx 15 mins (it is to completion so timing is not important)
rinse under running tap for approx 2 mins
soak in distilled water with a crop of liquid soap for approx 2 mins
I suppose I need to tweak my process until I figure out what's causing the white spots.
Because I'm doing a lot of film work, I think I'll invest in a Jobo rotary processor next year, Attila gets great results with his. _________________ I don't care who designed it, who made it or what country it comes from - I just enjoy using it! |
|
| Nach oben |
|
 |
Orio
Anmeldungsdatum: 24.02.2007 Beiträge: 29545 Wohnort: West Emilia
Expire: 2012-12-04
|
 Verfasst am: So Dez 09, 2012 4:50 pm Titel: |
|
 Verfasst am: So Dez 09, 2012 4:50 pm Titel: |
|
|
Orio wrote:
Sorry, I detailed my B&W steps, I forgot this was in colour.
Surely tap water is more dangerous with B&W because B&W film has more silver which means more occasions for calcar to attach to surface.
In any case, I think that not to use tap water until after first rinse would be safer.
But you make a lot more film rolls than I do, this of course means more use of distilled water. _________________ Orio, Administrator
T*
NE CEDE MALIS AUDENTIOR ITO
Ferrania film is reborn! http://www.filmferrania.it/
Support the Ornano film chemicals company and help them survive!
http://forum.mflenses.com/ornano-chemical-products-t55525.html |
|
| Nach oben |
|
 |
iangreenhalgh1
 Anmeldungsdatum: 18.03.2011 Beiträge: 15679
Expire: 2014-01-07
|
 Verfasst am: So Dez 09, 2012 5:36 pm Titel: |
|
 Verfasst am: So Dez 09, 2012 5:36 pm Titel: |
|
|
iangreenhalgh1 wrote:
Aah, I see, that makes sense, that is for BW.
I try to keep things as simple as possible, and I am pretty sure we have really good tap water here, being in the mountains, it's much better than you get in a city, it is always ph 6.2 and ec 0 so it doesn't have any dissolved solids in it unlike city water. I'm not sure if it's fluoridated, I don't think so. If you pour a glass of water straight from the tap it is perfectly clear and if you sit it there and watch it, there is no swirling then settling of particulates as I always got when I lived in a city.
I'll try doing it with just distileld water, it's about 1.50ukp for 5 litres so not all that expensive, but I'd prefer to be able to to use it if possible.
I don't get the white spot problem with my BW work, and on some 35mm frames I don't get any spots either. It's quite mysterious how some frames can be covered in white spots and another frame on the same roll can be spotless. _________________ I don't care who designed it, who made it or what country it comes from - I just enjoy using it! |
|
| Nach oben |
|
 |
|
|
|
Du kannst keine Beiträge in dieses Forum schreiben. Du kannst auf Beiträge in diesem Forum nicht antworten. Du kannst deine Beiträge in diesem Forum nicht bearbeiten. Du kannst deine Beiträge in diesem Forum nicht löschen. Du kannst an Umfragen in diesem Forum nicht mitmachen.
|