MFlenses - Ein neues Leben im digitalen Zeitalter
MFLenses 2026

Forum für Manual-Fokus-Objektive

Entdecke die Welt der Vintage-Objektive mit Reparaturnotizen, echten Testfotos und detaillierten Archiv-Themen voller Bilder.

Entdecke die Welt der Vintage-Objektive mit Reparaturnotizen, echten Testfotos und detaillierten Archiv-Themen voller Bilder.
Spotlight

Hervorgehobene Partnerplatzierung auf der Forum-Startseite.

Sling strap for your DSLR and wrist strap too!
Vorheriges Thema anzeigen :: Nächstes Thema anzeigen  


Reply

I've been looking at getting an 'over the shoulder' type of strap as I hate walking with my camera poking out. I've used the normal strap over my shoulder and it works reasonable well but the strap has to slide back over your shoulder as you lift the camera to use it. Difficult if you are wearing it under your coat.

I've seen the 'camera strap buddy' and thought that it was a good idea. I have a similar item on an old flexible metal wrist strap. so I cut the strap off and experimented. one half of the strap on the camera lug and the other through the tripod screw adapter. It worked but you still had the slidy strap problem. The Nikon strap has a non slidy coating under the wide bit.

I have been thinking of a design that will ensure total security for my camera. So inspired by Lloydy's design (elsewhere on this forum) I have modified the original strap from my Nikon. The camera can be quickly detached from the strap when necessary.




Parts needed:
1 original Nikon strap
1 tripod bush adapter ('camera strap buddy' is good but mine is less fiddly to put on and off)
1 extra strap, the same width as the ends of the Nikon's (or a 1 metre length of black webbing from a fabric shop)
fabric glue


Tools needed:
Sewing machine with a thickish needle
strong black thread
cigarette lighter
2 paperclips or sewing pins

Method:

I took the strap off the camera, clipped the ends together with a couple of paperclips and slung it over my shoulder to check the length. It seemed to be a bit short, ending just below my rib cage. Ok that can be dealt with later...

The first thing to do was to create a wrist strap for my camera. I threaded one end of the webbing through the screw adapter and glued it together, I pulled it through about 2.5cm. I threaded the other end of the strap through the left hand lug (as you hold the camera) and pulled it through. Holding the camera in my right hand I was able to judge how much webbing to use. I planned to use the buckle from the Nikon strap to allow it to adjust (and remove). When I was happy with the length I cut off the excess. Use the lighter to melt the ends of the webbing if it's nylon to stop it fraying.

After the glue has dried, sew the strap together at the screw adapter end. I sewed a rectangle round the length of the join then criss-crossed it a couple of times. cut the threads off with lots to spare and tie off the ends. snipping them as close to the strap as possible.

Thread it through the strap lug and use the adjust the to fit. Voila a wrist strap. and part one of this project finished.



The shoulder strap bit. Now try the shoulder strap for length threading it through the wrist strap. I was lucky, it rested just above my hip and was comfortable. All I had to do was sew the ends of the Nikon strap together.

BUT, a problem. I'd only be able to join about 1cm of each end, and that didn't seem enough. So I decided to attach the webbing along the entire strap from shoulder pad to shoulder pad (the wide bit with Nikon printed on it). I cut the webbing to length allowing an extra cm for stretch. I melted the ends to tidy them up, and put a couple of the loops that come with the strap over it before starting. These are to tidy up the join at both ends. I and fastened the webbing to the front of the strap, leaving the join hidden inside. Starting from one end to the other I stitched the webbing to the strap all the way down the centre, just to get it all together before the serious stitching. I used 20 stitches per inch setting on my machine.

[url=http://forum.mflenses.com/userpix/201212/big_5918_machine_1.jpg]
[/url]

When it was all together I stitched down both sides, did a little cris-cross box at the ends and where it joined then zigzagged all the way from one end to the other twice. There are about 20 metres of strong thread holding my strap together, probably more than a commercial one!. Tie off the ends of the thread and snip. The strap is quite stiff but when it's over the shoulder its extremely comfortable and practical.

Thread the wrist strap through it and attach to the camera. Job done.

[url=http://forum.mflenses.com/userpix/201212/big_5918_DSC_3066_1.jpg]
[/url]



I had originally thought of having one end adjustable, and for those of our members who are taller or fond of pies, you may like a longer strap. This can be achieved easily. The part of the strap that goes behind you does not have to be sewn together, instead, use the other buckle and attach the ends together that way. Snip the excess from the strap and adjust it to fit, and use the original square loops to keep it tidy.

If you like the closed loop design but its too short for you I would suggest using a length of the webbing to bridge the join where the Nikon's ends meet.

Tidying up.
I noticed in use the wrist trap would sometimes catch where the Nikon's ends were joined. So using a piece of thin leather (camera covering from an old praktica) I glued it over the join and left it clamped in a vice to set. I ran some stitches though it and the strap slides smoothly now. Cover the ends of the bridge piece too if you make that type.

good luck.


Zuletzt bearbeitet von philslizzy am Mi Dez 12, 2012 6:23 pm, insgesamt ein Mal bearbeitet


Reply

Good "brico"!.

Thanks for sharing!

Jes.


Reply

Jesito hat folgendes geschrieben::
Good "brico"!.

Thanks for sharing!

Jes.


Brico as in 'Do it Yourself?' Thanks anyway!!