MFlenses - Ein neues Leben im digitalen Zeitalter
MFLenses 2026

Forum für Manual-Fokus-Objektive

Entdecke die Welt der Vintage-Objektive mit Reparaturnotizen, echten Testfotos und detaillierten Archiv-Themen voller Bilder.

Entdecke die Welt der Vintage-Objektive mit Reparaturnotizen, echten Testfotos und detaillierten Archiv-Themen voller Bilder.
Spotlight

Hervorgehobene Partnerplatzierung auf der Forum-Startseite.

I need help to fix aperture of Pancolar 80/1.8
Vorheriges Thema anzeigen :: Nächstes Thema anzeigen  


Reply

As usualy, this happens when I fix a lens - thse are left-overs after I reassembled the lens:



After several hours of failed attempts I just gave up and rebuilt the lens witout these items. I just can't get the blades in their place. And even though I took photos while tearing the lens apart, I am not at all sure how the blades should be arranged any more. I am just too stipid for stuff like this and I would really like to have one or two of extra hands coming from my torso.

This is a quick and dirty classing shoot-the-bill-test - it's a bit off center crop, not even sure if it is in focus, don't care at this hour - also, it's ISO 4.000+, so excuse the noise (and it's negative influence on the resolving ability).



I am sure I need not mention what the lens is - it cost me about 160 euros or so.


Reply

Ah yes, the "I need four hands with 7 fingers each" feeling. I know it well Smile
Alternating with the "I need one hand with twenty fingers" feeling Smile

I am not familiar with this particular lens but, once everything has been cleaned.....

Of the two rings on the left of your picture, I think you start with the large one then lay the other ring inside it. Each aperture blade should have two pins, one of which will engage in a slot/indentation in the large ring, the other in a slot/indentation in the smaller ring. Lay one blade on the rings with the pins in the slots. By turning one ring in relation to the other, the aperture blade should "close down" in the manner to which we are accustomed.

Once you can see how a single blade works in relation to the rings, it is "merely" a question of added successive blades, each one on top of the previous. Of course, when you get to the last one, it has to be sort of inserted between the first one you placed and the last one you placed. This is tricky Smile

At this stage, turning the rings in relation to each other should result in a fully functioning aperture. Be careful, because at this stage (or any other Smile) success can be torn from your grasp by all the blades becoming dislodged (accompanied by much cursing) Smile

Either the large ring on the right of your picture, or the lens body, itself will keep the blade in place once everything is assembled.

Of course, as you have shown, it works very well with no aperture at all Smile


Reply

martyn_bannister hat folgendes geschrieben::
Ah yes, the "I need four hands with 7 fingers each" feeling. I know it well Smile
Alternating with the "I need one hand with twenty fingers" feeling Smile

I am not familiar with this particular lens but, once everything has been cleaned.....

Of the two rings on the left of your picture, I think you start with the large one then lay the other ring inside it. Each aperture blade should have two pins, one of which will engage in a slot/indentation in the large ring, the other in a slot/indentation in the smaller ring. Lay one blade on the rings with the pins in the slots. By turning one ring in relation to the other, the aperture blade should "close down" in the manner to which we are accustomed.

Once you can see how a single blade works in relation to the rings, it is "merely" a question of added successive blades, each one on top of the previous. Of course, when you get to the last one, it has to be sort of inserted between the first one you placed and the last one you placed. This is tricky Smile

At this stage, turning the rings in relation to each other should result in a fully functioning aperture. Be careful, because at this stage (or any other Smile) success can be torn from your grasp by all the blades becoming dislodged (accompanied by much cursing) Smile

Either the large ring on the right of your picture, or the lens body, itself will keep the blade in place once everything is assembled.

Of course, as you have shown, it works very well with no aperture at all Smile


While I appreciate the help, it big problem not so much putting the blades into the two-ring-construction (takes two hours of careful play with inadequate tools and hands of mine Wink ), but managing to get this loose construction somehow into the lens in one piece. The 180/2.8 and 300/4 aperture mechanism was a bit simpler in that there were no two separate round rings torturing the service person, though somehow the 180 is still lacking the aperture mechanismm Wink

I did take tons of shots when I tore the lens apart, but mostly the wrong pictures Sad Even though the two rings and the blades are all now nicely connected, but I am not at all sure the two rings are positioned properly relative to each other - it is possible one (though probably not the other) should be flipped upside down. Anyhow, it seems as it there is nothing really preventing these construction from collapsing if I just dare to try to life it up, though turning it all upside down might help, at least if the blades just manage to hold themselves together.

I will probably try to fix the darn thng next week once I buy better tools and/or get even more help and instructions.


Reply

Perhaps blades have to be assembled inside lens? I had one like that. Long tweezers and a lot of patience required Smile

"If it came apart, one must be able to put it back together"

If you get sick of it, just send it to me. I love a puzzle Smile Smile Smile


Reply

martyn_bannister hat folgendes geschrieben::
Perhaps blades have to be assembled inside lens? I had one like that. Long tweezers and a lot of patience required Smile

"If it came apart, one must be able to put it back together"

If you get sick of it, just send it to me. I love a puzzle Smile Smile Smile


I had not even given a though of that - an excellent idea! I do need to get the tweezers first: sometimes the right tools are of help Wink

I also managed to lose the tiny spring (one of the two) - I though losin it would be impossible, but somehow... I am pretty sure I have a replacement though.

I have made a couple of observations about this lens - first is that there just too much plastic inside the lens. I am tempted at replacing the plastic "legs" to metal ones from another lens.

The other observation is about focus calibration. I will probably take a couple of shots as I still need to make a smalll adjustment. This lens has a two-stage focus calibration and I think a Nikon user should have a look at this lens with a glassless adapter as I am pretty sure the infinity can be reached with Nikon as well and proper adjustment.

A though hit me today - does any of the other CZJ lenses share the same aperture mechanism with 80/1.8 Pancolar, like for example the medium format 300 and 180 do? Anyone?


Reply

It is similar to the Pancolar 50mm f1.8 I cleaned just recently, yesterday, or so it seems.
the two rings on the left of your picture are assembled first with little one inside.
The extensions of small one in the place of the inside cut of the other, then assemble the blades.
Blades are placed in clockwise order, the last one comes over previous and beneath first.
In 50mm there was another ring placed on top then came the rightmost ring from your picture. and after that a screw ring.

I have pictures with all parts if you want I can send or post here.

Good luck.
Hope it helps.


Reply

sadness hat folgendes geschrieben::
It is similar to the Pancolar 50mm f1.8 I cleaned just recently, yesterday, or so it seems.
the two rings on the left of your picture are assembled first with little one inside.
The extensions of small one in the place of the inside cut of the other, then assemble the blades.
Blades are placed in clockwise order, the last one comes over previous and beneath first.
In 50mm there was another ring placed on top then came the rightmost ring from your picture. and after that a screw ring.

I have pictures with all parts if you want I can send or post here.

Good luck.
Hope it helps.


Thank you!

I would appreciate the imagery much, but maybe it would better if they'd start up a new thread so that people seeking help for 50/1.8 might find it easier to find it by searching.

Pictures are always worth more than a few words - even in photography forum Smile