MFlenses - Ein neues Leben im digitalen Zeitalter
MFLenses 2026

Forum für Manual-Fokus-Objektive

Entdecke die Welt der Vintage-Objektive mit Reparaturnotizen, echten Testfotos und detaillierten Archiv-Themen voller Bilder.

Entdecke die Welt der Vintage-Objektive mit Reparaturnotizen, echten Testfotos und detaillierten Archiv-Themen voller Bilder.
Spotlight

Hervorgehobene Partnerplatzierung auf der Forum-Startseite.

Quick makeover
Vorheriges Thema anzeigen :: Nächstes Thema anzeigen  


Reply

My first attempt at replacing deteriorated leatherette. The recovered camera was worse than the camera shown on the right. I'm happy with it as a first effort. I'll do it again to improve the fit and use a more secure glue.



Reply

Looks nice really on picture. You made great job!


Reply

Does look good. Was it a kit or did you cut it yourself?


Reply

All hand cut from a ladies shoulder bag bought for 50 cents! The old stuff peeled off quite gracefully and I was able to use it as a pattern. There's enough material left to do several more cameras. I'm doing the second one now. Perhaps I'll get some pictures and post a "how to".


Reply

Good idea...
I've done a couple, one with a kit and one with a desk diary and have a couple of handbags from charity shops which I've cut up ready, but worry that the leather is too 'stretchy' to cut to the right size... it changes shape as I cut!
Did you have any trouble? Maybe if it were fixed to some card first and then cut...?


Reply

Xpres,

Sorry for coming in late.

Although I use pre-cut replacement coverings, I have done a bit of very precise cutting of stretchy materials.

The key is not to use a normal blade, as it cuts it pulls the material as well, stretching it along the way; you want the cutting edge to fall straight down, cutting through the material without up-down stretching too.

The cutting tool you need would be a roller cutter; a common brand is "Olfa", which is a handle holding free-spinning steel cutting wheel, which gives the straight-down cutting action. To prevent vertical stretching, do not use a rubber cutting mat, use a sheet of glass instead. If you are cutting a straight line, also use a good straight edge to hold the material down securely too.


Reply

Fantastic advice - thank you! Very Happy


Reply

Nice job !
ihave done quite a few and found the best to use is this pressure sensitive transparent doublesided tape it is very thin and sticks like crazy
just pull it of the roll and cover the whole inside of the leatherette then pull of the backing and apply the whole letherette like a sticker
it is very close to the original stuff they use in the factory and when you pull it of again it leaves nothing on the camera


Reply

casualcollector hat folgendes geschrieben::
My first attempt at replacing deteriorated leatherette.

Nice job.


Reply

I've used the double sided sticky tape to replace original leatherette once. It worked well. I haven't found similar product locally, yet. I used Elmer's brand rubber cement for this project. It's a fairly tame, craft style material that's intended to be easy to remove. Not good enough. I've not found Pliobond, locally, either. Have to go to the next bigger town and look!

The material I used has a loosely woven backing and is stretchy. I cut it with an X-Acto hobby knife with a fresh blade. I also used a steel scale for all of the straight cuts. It worked well enough. The roller cutter would work better for straight cuts.

Here's the details...



The small screwdriver was used to lift the corner of the leatherette. The plastic pen cap was used to gently scrape up the end. Pulling up from both corners minimizes distortion of the covering.



As the covering was still sticky I pressed it down onto some stiff, thin cardstock to make patterns. The patterns were cut from the paper with the hobby knife.



Several light cuts were made with the hobby knife to minimize stretching of the new material. I'm going to wait until I have some better adhesive to finish the second camera.