| Vorheriges Thema anzeigen :: Nächstes Thema anzeigen |
| Autor |
Nachricht |
Marlon Managi
Anmeldungsdatum: 11.03.2014 Beiträge: 12 Wohnort: Bali, Indonesia
|
 Verfasst am: So Dez 21, 2014 9:20 am Titel: How to Fix Asahi Camera Light Meter |
|
 Verfasst am: So Dez 21, 2014 9:20 am Titel: How to Fix Asahi Camera Light Meter |
|
|
Marlon Managi wrote:
Asahi Pentax is one of the famous brand camera from Japan beside Nikon, Canon, and Minolta. Great built in body and its looks like samurai warrior from Japan. But nowadays I often found Asahi Pentax camera in junk store or second hand camera store in dead light meter condition. Several conditions might be caused the light meter doesn’t work such as : due its age, copper wire inside light meter is coated by rush, broken copper wire etc. If you are analog lover is so sad to facing this condition. After several experiments I found some way to fix and bring the light meter back to normal. This method Couldn't fix your light meter if the copper wire inside the light meter is broken.
What equipment you may need?
1. Single battery which has capacity 1.5Volt
2. wires
3. Tape
4. Scissor
Step by step
1.Open battery cap chamber in bottom plate of you camera.
2.After that you will find 2 contact surfaces. One is for negative pole, and second one is for positive pole.
3. Take your battery and install the wire in both side pole of you battery using tape.
4. Before you apply to using battery and wire please make sure you light meter switch is on position.
5.This is the IMPORTANT step you should pay attention. After you install the wire with battery now get ready for this part. Take the wire from positive pole from you battery put it on bottom plate(near by the hole) and take the wire form negative pole and RUBBING in surface area inside battery chamber, DO NOT Allowed the wire contact for long time to avoid overload circuit.
6. Be careful do not MISPLACED between positive pole and negative pole. Because this camera using DC circuit, to avoid short circuit.
7. And after those steps are applied install small battery (watch battery or LR44 battery) and check your light meter. Hope it becoming normal and work properly.
Best Regards, Marlon
NOTE : You applied this method with your OWN RISK.
_________________ Very nice to find this website. Hope Admin can accept me to join in this website. By the way, I love manual lenses. Hahhaha. LOL
Zuletzt bearbeitet von Marlon Managi am Di Dez 30, 2014 7:55 am, insgesamt ein Mal bearbeitet |
|
| Nach oben |
|
 |
DigiChromeEd
 Anmeldungsdatum: 29.12.2009 Beiträge: 3468 Wohnort: Northern Ireland
|
 Verfasst am: So Dez 21, 2014 9:34 am Titel: Re: How to Fix Asahi Camera Light Meter |
|
 Verfasst am: So Dez 21, 2014 9:34 am Titel: Re: How to Fix Asahi Camera Light Meter |
|
|
DigiChromeEd wrote:
Hi Marlon Managi, welcome to the forum!
You can't post photos or links in your first post - an antispam measure. You'll be ok from now on.
| Marlon Managi hat folgendes geschrieben:: |
Asahi Pentax is one of the famous brand camera from Japan beside Nikon, Canon, and Minolta. Great built in body and its looks like samurai warrior from Japan. But nowadays I often found Asahi Pentax camera in junk store or second hand camera store in dead light meter condition. Several conditions might be caused the light meter doesn’t work such as : due its age, copper wire inside light meter is coated by rush, broken copper wire etc. If you are analog lover is so sad to facing this condition. After several experiments I found some way to fix and bring the light meter back to normal. This method Couldn't fix your light meter if the copper wire inside the light meter is broken.
What equipment you may need?
1. Single battery which has capacity 1.5Volt
2. wires
3. Tape
4. Scissor
Step by step
1.Open battery cap chamber in bottom plate of you camera.
2.After that you will find 2 contact surfaces. One is for negative pole, and second one is for positive pole.
3. Take your battery and install the wire in both side pole of you battery using tape.
4. Before you apply to using battery and wire please make sure you light meter switch is on position.
5.This is the IMPORTANT step you should pay attention. After you install the wire with battery now get ready for this part. Take the wire from positive pole from you battery put it on bottom plate(near by the hole) and take the wire form negative pole and RUBBING in surface area inside battery chamber, DO NOT Allowed the wire contact for long time to avoid overload circuit.
6. Be careful do not MISPLACED between positive pole and negate pole. Because this camera using DC circuit, to avoid short circuit.
7. And after those steps are applied install small battery (watch battery or LR44 battery) and check your light meter. Hope it becoming normal and work properly.
Best Regards, Marlon
NOTE : You applied this method with your OWN RISK.
|
_________________ "I've got a Nikon camera, I like to take a photograph" - Paul Simon |
|
| Nach oben |
|
 |
kuuan
 Anmeldungsdatum: 14.01.2008 Beiträge: 4569 Wohnort: right now: Austria
Expire: 2014-12-26
|
 Verfasst am: So Dez 21, 2014 2:39 pm Titel: |
|
 Verfasst am: So Dez 21, 2014 2:39 pm Titel: |
|
|
kuuan wrote:
welcome here Marlon, and thank you very much for your very interesting and helpful post!
may many Spoty lightmeters be kicked to life! _________________ my photos on flickr: https://www.flickr.com/photos/kuuan/collections |
|
| Nach oben |
|
 |
Marlon Managi
Anmeldungsdatum: 11.03.2014 Beiträge: 12 Wohnort: Bali, Indonesia
|
 Verfasst am: Di Dez 30, 2014 6:47 am Titel: Re: How to Fix Asahi Camera Light Meter |
|
 Verfasst am: Di Dez 30, 2014 6:47 am Titel: Re: How to Fix Asahi Camera Light Meter |
|
|
Marlon Managi wrote:
| DigiChromeEd hat folgendes geschrieben:: |
Hi Marlon Managi, welcome to the forum!
You can't post photos or links in your first post - an antispam measure. You'll be ok from now on.
| Marlon Managi hat folgendes geschrieben:: |
Asahi Pentax is one of the famous brand camera from Japan beside Nikon, Canon, and Minolta. Great built in body and its looks like samurai warrior from Japan. But nowadays I often found Asahi Pentax camera in junk store or second hand camera store in dead light meter condition. Several conditions might be caused the light meter doesn’t work such as : due its age, copper wire inside light meter is coated by rush, broken copper wire etc. If you are analog lover is so sad to facing this condition. After several experiments I found some way to fix and bring the light meter back to normal. This method Couldn't fix your light meter if the copper wire inside the light meter is broken.
What equipment you may need?
1. Single battery which has capacity 1.5Volt
2. wires
3. Tape
4. Scissor
Step by step
1.Open battery cap chamber in bottom plate of you camera.
2.After that you will find 2 contact surfaces. One is for negative pole, and second one is for positive pole.
3. Take your battery and install the wire in both side pole of you battery using tape.
4. Before you apply to using battery and wire please make sure you light meter switch is on position.
5.This is the IMPORTANT step you should pay attention. After you install the wire with battery now get ready for this part. Take the wire from positive pole from you battery put it on bottom plate(near by the hole) and take the wire form negative pole and RUBBING in surface area inside battery chamber, DO NOT Allowed the wire contact for long time to avoid overload circuit.
6. Be careful do not MISPLACED between positive pole and negate pole. Because this camera using DC circuit, to avoid short circuit.
7. And after those steps are applied install small battery (watch battery or LR44 battery) and check your light meter. Hope it becoming normal and work properly.
Best Regards, Marlon
NOTE : You applied this method with your OWN RISK.
|
|
Wow many thx buddy glad to hear that. thx for appreciated my thread  _________________ Very nice to find this website. Hope Admin can accept me to join in this website. By the way, I love manual lenses. Hahhaha. LOL |
|
| Nach oben |
|
 |
Marlon Managi
Anmeldungsdatum: 11.03.2014 Beiträge: 12 Wohnort: Bali, Indonesia
|
 Verfasst am: Di Dez 30, 2014 6:49 am Titel: |
|
 Verfasst am: Di Dez 30, 2014 6:49 am Titel: |
|
|
Marlon Managi wrote:
| kuuan hat folgendes geschrieben:: |
welcome here Marlon, and thank you very much for your very interesting and helpful post!
may many Spoty lightmeters be kicked to life! |
Thx buddy. I tried this trick for several times and its work bring my asahi takumar light meter back to work. Thx for visiting my thread  _________________ Very nice to find this website. Hope Admin can accept me to join in this website. By the way, I love manual lenses. Hahhaha. LOL |
|
| Nach oben |
|
 |
philslizzy
 Anmeldungsdatum: 07.08.2012 Beiträge: 4753 Wohnort: Cheshire, England
|
 Verfasst am: Di Dez 30, 2014 7:12 am Titel: |
|
 Verfasst am: Di Dez 30, 2014 7:12 am Titel: |
|
|
philslizzy wrote:
Interesting idea. I wonder how it works and if it would work with other cameras. _________________ Hero in the 'messin-with-cameras-for-the-hell-of-it department'. Official. |
|
| Nach oben |
|
 |
Marlon Managi
Anmeldungsdatum: 11.03.2014 Beiträge: 12 Wohnort: Bali, Indonesia
|
 Verfasst am: Di Dez 30, 2014 7:49 am Titel: |
|
 Verfasst am: Di Dez 30, 2014 7:49 am Titel: |
|
|
Marlon Managi wrote:
| philslizzy hat folgendes geschrieben:: |
| Interesting idea. I wonder how it works and if it would work with other cameras. |
I had tried it on Minolta SRT 101 which is the light meter isn't work and when i use this technique for "electric shocking"
and the metering is work now  _________________ Very nice to find this website. Hope Admin can accept me to join in this website. By the way, I love manual lenses. Hahhaha. LOL |
|
| Nach oben |
|
 |
philslizzy
 Anmeldungsdatum: 07.08.2012 Beiträge: 4753 Wohnort: Cheshire, England
|
 Verfasst am: Di Dez 30, 2014 9:49 pm Titel: |
|
 Verfasst am: Di Dez 30, 2014 9:49 pm Titel: |
|
|
philslizzy wrote:
| Marlon Managi hat folgendes geschrieben:: |
| philslizzy hat folgendes geschrieben:: |
| Interesting idea. I wonder how it works and if it would work with other cameras. |
I had tried it on Minolta SRT 101 which is the light meter isn't work and when i use this technique for "electric shocking"
and the metering is work now  |
Minolta SRT101 was the very camera I had in mind! _________________ Hero in the 'messin-with-cameras-for-the-hell-of-it department'. Official. |
|
| Nach oben |
|
 |
Marlon Managi
Anmeldungsdatum: 11.03.2014 Beiträge: 12 Wohnort: Bali, Indonesia
|
 Verfasst am: Mi Dez 31, 2014 1:07 am Titel: |
|
 Verfasst am: Mi Dez 31, 2014 1:07 am Titel: |
|
|
Marlon Managi wrote:
| philslizzy hat folgendes geschrieben:: |
| Marlon Managi hat folgendes geschrieben:: |
| philslizzy hat folgendes geschrieben:: |
| Interesting idea. I wonder how it works and if it would work with other cameras. |
I had tried it on Minolta SRT 101 which is the light meter isn't work and when i use this technique for "electric shocking"
and the metering is work now  |
Minolta SRT101 was the very camera I had in mind! |
This is my minolta SRT buddy
Great camera also _________________ Very nice to find this website. Hope Admin can accept me to join in this website. By the way, I love manual lenses. Hahhaha. LOL |
|
| Nach oben |
|
 |
inombrable
 Anmeldungsdatum: 20.03.2012 Beiträge: 545 Wohnort: Salamanca, Mexico
|
 Verfasst am: Sa Jan 03, 2015 6:12 am Titel: |
|
 Verfasst am: Sa Jan 03, 2015 6:12 am Titel: |
|
|
inombrable wrote:
Awesome !!
Just to let you know it worked on my alpa 9D, now the meter is back to life and to my surprise seems to be very accurate.
Thanks a lot. _________________ -----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
DSLR: Canon 5D, Nikon D200
SLR: Alpa 9d, Voigtlander VSL3E, Contax D
Medium Format: Hasselblad 500 EL/M, Praktisix, Rolleiflex standar 621
Rangefinder: Contax II, Contax III, Leica M2, Leica M4, Leica IIC, Nikon S2
M42:CZJ Flektogon 20 f/2.8, CZJ Flektogon 25 f/4, CZJ Flektogon 35 f/2.4, Color Skoparex 35 f/2.8, CZJ Pancolar 50 f/1.8, Super takumar 50 f/1.4, Meyer Primoplan 58 f/1.9, CZJ Tessar 50 f/2.8 alu, Jupiter 9 MC, Super Takumar 105 f/2.5, SMC Takumar 135 f/2.5, CZJ Sonnar 135 f/3.5 MC, CZJ Sonnar 135 f/3.5 Zebra, Super takumar 200 f/3.5
Nikon mount: Nippon kogaku Nikkor-N Auto 24 f/2.8, Nikon micro Nikkor 55 f/2.8, Kiron 105 f/2.8 macro.
C/Y: Planar 50 f/1.4, Yashica ML 50 f/1.4, Planar 85 f/1.4.
M39: Mir-1 Grand Prix Brussels, Helios 44 13 blades, Jupiter 11
Rangefinder: CZJ Biogon 3.5cm f/2.8, Sonnar 50 f/1.5, Sonnar 50 f/2, Nikkor-S 5 cm f/1.4, Summicron 50 f/2 DR, Summicron 50 f/2 collapsible, Summicron 35 f/2 V3. Jupiter 12, Jupiter 8, Jupiter 9, Elmar 90 f/4.
Canon EF: Voigtlander APO-Lanthar 90 f/3.5 SL-II
Exakta: Biotar 58 f/2
Adaptall: 103A, 46A, 19AH, 55B
|
|
| Nach oben |
|
 |
tromboads
 Anmeldungsdatum: 29.05.2012 Beiträge: 1695 Wohnort: Melbourne AU
Expire: 2015-10-01
|
 Verfasst am: Sa Jan 03, 2015 8:40 am Titel: |
|
 Verfasst am: Sa Jan 03, 2015 8:40 am Titel: |
|
|
tromboads wrote:
I'm a bit confused here.. you are just passing a broken current to the meter in effort to "re-boot it" ?? |
|
| Nach oben |
|
 |
Lloydy
 Anmeldungsdatum: 02.09.2009 Beiträge: 7880 Wohnort: Ironbridge. UK.
Expire: 2022-01-01
|
 Verfasst am: Sa Jan 03, 2015 11:39 am Titel: |
|
 Verfasst am: Sa Jan 03, 2015 11:39 am Titel: |
|
|
Lloydy wrote:
I've heard about flashing a higher voltage across some electrical / electronic devices to resurrect them before. My guess is - it's a kill or cure technique. _________________ LENSES & CAMERAS FOR SALE.....
I have loads of stuff that I have to get rid of, if you see me commenting about something I have got and you want one, ask me.
My Flickr https://www.flickr.com/photos/mudplugga/
My ipernity -
http://www.ipernity.com/home/294337 |
|
| Nach oben |
|
 |
philslizzy
 Anmeldungsdatum: 07.08.2012 Beiträge: 4753 Wohnort: Cheshire, England
|
 Verfasst am: So Jan 04, 2015 10:55 pm Titel: |
|
 Verfasst am: So Jan 04, 2015 10:55 pm Titel: |
|
|
philslizzy wrote:
Perhaps its the higher amperage, The circuit in the camera can deal with 1.5 volts easy enough. I've got to give it a go! _________________ Hero in the 'messin-with-cameras-for-the-hell-of-it department'. Official. |
|
| Nach oben |
|
 |
Marlon Managi
Anmeldungsdatum: 11.03.2014 Beiträge: 12 Wohnort: Bali, Indonesia
|
 Verfasst am: Di Jan 06, 2015 5:38 am Titel: |
|
 Verfasst am: Di Jan 06, 2015 5:38 am Titel: |
|
|
Marlon Managi wrote:
| inombrable hat folgendes geschrieben:: |
Awesome !!
Just to let you know it worked on my alpa 9D, now the meter is back to life and to my surprise seems to be very accurate.
Thanks a lot. |
Wow glad to hear that. you made it congrats. then now play around with your analog camera  _________________ Very nice to find this website. Hope Admin can accept me to join in this website. By the way, I love manual lenses. Hahhaha. LOL |
|
| Nach oben |
|
 |
Marlon Managi
Anmeldungsdatum: 11.03.2014 Beiträge: 12 Wohnort: Bali, Indonesia
|
 Verfasst am: Di Jan 06, 2015 5:41 am Titel: |
|
 Verfasst am: Di Jan 06, 2015 5:41 am Titel: |
|
|
Marlon Managi wrote:
| tromboads hat folgendes geschrieben:: |
| I'm a bit confused here.. you are just passing a broken current to the meter in effort to "re-boot it" ?? |
Definitely yes bro. That's what i mean "Electrical shocking"  _________________ Very nice to find this website. Hope Admin can accept me to join in this website. By the way, I love manual lenses. Hahhaha. LOL |
|
| Nach oben |
|
 |
philslizzy
 Anmeldungsdatum: 07.08.2012 Beiträge: 4753 Wohnort: Cheshire, England
|
 Verfasst am: Di Jan 06, 2015 10:00 am Titel: |
|
 Verfasst am: Di Jan 06, 2015 10:00 am Titel: |
|
|
philslizzy wrote:
| Marlon Managi hat folgendes geschrieben:: |
...then now play around with your analog camera  |
'analog' grrr... _________________ Hero in the 'messin-with-cameras-for-the-hell-of-it department'. Official. |
|
| Nach oben |
|
 |
Marlon Managi
Anmeldungsdatum: 11.03.2014 Beiträge: 12 Wohnort: Bali, Indonesia
|
 Verfasst am: Mi Jan 07, 2015 12:31 pm Titel: |
|
 Verfasst am: Mi Jan 07, 2015 12:31 pm Titel: |
|
|
Marlon Managi wrote:
| philslizzy hat folgendes geschrieben:: |
| Perhaps its the higher amperage, The circuit in the camera can deal with 1.5 volts easy enough. I've got to give it a go! |
Okay then let me know if you already fix it  _________________ Very nice to find this website. Hope Admin can accept me to join in this website. By the way, I love manual lenses. Hahhaha. LOL |
|
| Nach oben |
|
 |
|
|
|
Du kannst keine Beiträge in dieses Forum schreiben. Du kannst auf Beiträge in diesem Forum nicht antworten. Du kannst deine Beiträge in diesem Forum nicht bearbeiten. Du kannst deine Beiträge in diesem Forum nicht löschen. Du kannst an Umfragen in diesem Forum nicht mitmachen.
|